Copyright 2007 by Harbor Freight Tools®. All rights reserved. No portion of thismanual or any artwork contained herein may be reproduced in any sha
3. Secure the Manual Elevation Handle (5) with a Cap Screw (7).(See Figure D.)4. Insert the Plug (6) into the Manual Elevation Handle (5) to cover the
SKU 95518 For technical questions, please call 1-800-444-3353 PAGE 11out of the Power Switch. The Power Switch cannot be turned on wit
SKU 95518 For technical questions, please call 1-800-444-3353 PAGE 12Rollercase 1/16”. The manual elevation Handle is located on the t
SKU 95518 For technical questions, please call 1-800-444-3353 PAGE 13thickness reaches 1-1/4”.NOTE: To reset for a different depth sto
3. Boards longer than 24” should be supported (on both the infeed and outfeedsides of the Planer) by roller stands (not included). Do not plane board
cal wiring, and any other condition that may affect its safe operation. If abnormalnoise or vibration occurs, have the problem corrected before furth
F. Reverse the two planing Knives (173), or replace with new Knives and care- fully position each Knife on the two Knife Location Colla
E. Loosen the two Head Socket Head Screws (159) on the Idler Bracket (156). Then loosen the Chain (52) by sliding the Idler Bracket. (See Figure
TROUBLESHOOTINGProblem Possible Cause Possible Solution Gouging at ends of board. 1. Dull Knives. 2. Inadequate support of long boards. 3. Rolle
PARTS LIST - PLANER UNITNOTE:Some parts are listed and shown for illustration purposes only,and are not available individually as replacement parts.Pa
PRODUCT SPECIFICATIONSSAVE THIS MANUALYou will need this manual for the safety warnings and precautions, assembly,operating, inspection, maintenance a
PARTS LIST - PLANER UNIT (CONT.)NOTE:Some parts are listed and shown for illustration purposes only,and are not available individually as replacement
PARTS LIST - PLANER UNIT (CONT.)NOTE:Some parts are listed and shown for illustration purposes only,and are not available individually as replacement
ASSEMBLY DIAGRAM - PLANER UNITNOTE:Some parts are listed and shown for illustration purposes only,and are not available individually as replacement pa
ASSEMBLY DIAGRAM - PLANER UNIT (CONT.)NOTE:Some parts are listed and shown for illustration purposes only,and are not available individually as replac
PARTS LIST & ASSEMBLY DIAGRAM - MOTOR UNITNOTE:Some parts are listed and shown for illustration purposes only,and are not available individually a
IMPORTANT WARRANTY INFORMATIONSKU 95518 For technical questions, please call 1-800-444-3353 PAGE 25Harbor Freight Tools Co. makes every
ELECTRICAL SAFETY1. Grounded tools must be plugged into an outlet properly installed andgrounded in accordance with all codes and ordinances. Never r
in. Plugging in power equipment with the Power Switch on, invites accidents.5. Remove adjusting keys or wrenches before turning the power tool on. A
SPECIFIC SAFETY RULES1. Maintain labels and nameplates on the Planer. These carry important infor-mation. If unreadable or missing, contact Harbor F
12. Turn off the Planer and allow the unit to stop on its own if the workpiece isto be backed out of an uncompleted cut.SKU 95518 For technica
25. Always stand off to one side of the Planer when in use.26. Do not reach across the Planer when it is on.SKU 95518 For technical questions,
SKU 95518 For technical questions, please call 1-800-444-3353 PAGE 8double insulation system which satisfies OSHA requirements and comp
SKU 95518 For technical questions, please call 1-800-444-3353 PAGE 9SYMBOLOGYFIGURE CUNPACKINGWhen unpacking, check to make sure all th
Commentaires sur ces manuels